AVG Autotech Controls
Autotech Controls HomeAbout Autotech ControlsSupportDownloadsFree CatalogsContact Autotech Controls

M1950-P10 Specifications

GENERAL:
Power Requirements:
    120VAC+/- 10%, 50-60 Hz., 24VA
    240VAC+/- 10%, 50-60 Hz., 24VA
    (Optional)
Operating Temperature:
    -10°F to 130°F (-23°C to 55°C)
Position Transducer:
    Single turn resolver such as RL100;
    with CBL-10T22-Mxxx cable, 2,500 ft. max.
Supervisory, Brake Input and Brake Reset Inputs:
Optically isolated
    TRUE: Contact closure to VS- (common)
    FALSE: Open circuit
Motion Detector & Brake Monitor
Motion Detector Limits:
    2, Low & High. programmable; Motion detector
    output energizes when the resolver RPM is
    between low and high limits.
Brake Monitor:
    Normally energized, de-energizes when press
    stopping time (0-9.99 sec) exceeds programmed
    danger limit - 2nd caution output energized
    when stopping time exceeds caution limit.
Brake Input:
    Brake timing starts when the input becomes TRUE.
    # of PLS Programs/Set-ups:
    up to 100, keypad selectable
Scale factor: Programmable 16-999
Offset:
    Programmable from 0-Scale
    Factor, common to all programs

PLS Module

Scan Time:
    100-280 microseconds
No of PLS outputs:
    16 per module, optically isolated,
    “P” or “N” factory ordered

Die Protection Module

Number of inputs:
    8, optically isolated; all inputs “P”
    type or “N” type, factory ordered
Event Detection:
    Programmable rising edge, falling edge
    or pulse detection within programmed window.
Fault Outputs:
    All outputs either “P” or “N” type (see GENERAL
    section), factory ordered Faults because of the
    non-occurrence of event can be assigned
    to activate one of the two outputs:
Top Stop: Stops press at top
E-Stop:
    To stop press immediately
2 Pre-set Counters:
    Outputs energize at 0 count

Shut Height Module

Position Transducer:
    RL210, 128:1 geared Dual Resolver
Outputs:
    Outputs to motorized slide adjust
    to move in Up and Down directions.

Peak Load Monitor Module

Load Sensor:
    AVG-Autotech’s Load Sensor with
    built-in electronics to provide
    4-20mA current signal
Number of Sensors:
    4 per module
Outputs:
    4 to detect Positive & Negative tonnage
    press limits, Over & Under Die Limits

Tonnage at Angle

Load Sensor:
    AVG-Autotech’s Load Sensor with built-in
    electronics to provide 4-20mA current signal
Number of Sensors: 4 per module
Outputs: All outputs “P” or “N” type, factory ordered
Press Safe:
    Normally energized; de-energized when peak tons
    exceed programmed max. limit
Die Safe:
    Normally energized, de-energized when acquired
    tonnage profile lies outside the programmed
    band around stored reference profile
QC Alarm:
    Energized when number of bad parts exceed
    programmed limit (a part is considered bad if
    acquired tonnage profile is
    outside programmed QC band)
Serial Communication:
(Required for tonnage
signature on PC)

    RS485 multi-drop

Remote Power Relay Outputs

    All modules with NPN sinking output can use
    remote power relay chassis to provide higher
    power outputs. The relay supported are
    electromechanical (10A@120VAC),
    AC solid-state (3A@24-280VAC) and DC
    solid-state (3A@9-60VDC or 1A@0-200VDC).

“Ready-to-install” system package part numbers

  • SYS-P1950-P10:
    M1950 with RL100 resolver with 30 ft. of resolver cable
  • 16 output PLS module
  • 8 input Die Protect module
  • 4 input Peak Load Monitor unit with 4 Load sensors & sensor mounting kits
  • Shut Height control with RL210 resolver &
  • 30 ft. of resolver cable

Home | About Us | Support | Downloads | Free Catalogs | Contact

Copyright © 2014 Autotech Controls. All rights reserved. All Product names, trademarks and registered trademarks are the property of their respective manufacturers or legal holders. Autotech Controls disclaims any proprietary interest in the marks or names of others. All prices are US List prices and are subject to change without notice.