M1250, M1450, and M1451 Mini PLS
| 1.
MINI•PLS System Components
|
|
| 2. MINI•PLS | |
| Select one of the following Single-Turn Rotary PLSs for front panel mounting. Cam modules or power outputs are not included: | |
| SAC-M1250-010
|
3-Digit, single-turn,
basic unit
|
| SAC-M1450-300
|
3-Digit, single-turn,
with ModZ and speed compensation
|
| SAC-M1450-400
|
4-Digit, single-turn,
with ModZ and speed compensation
|
| SAC-M1451-010
|
3-Digit, single-turn,
with ModZ, speed compensation and brake monitor
|
| SAC-M1450-MROF
|
3-Digit, single-turn
with speed compensation and multiple rate offset
|
| 1.2 Select one of the
following Multi-turn Linear PLS’s for front panel mounting:
|
|
| Select one of the following Multi-turn Linear PLSs for front panel mounting. Cam modules or power outputs not included:
|
|
| SAC-M1450-M10
|
6-Digit, single
resolver, semi-absolute, basic unit
|
| SAC-M1450-D64
|
6-Digit, dual resolver
64:1 ratio, basic unit
|
| SAC-M1450-D128
|
6-Digit, dual resolver,
128:1 ratio, basic unit
|
| Linear PLS for front-panel mounting. No cam modules or power outputs included: | |
| SAC-1450-LT0
|
6-Digit, Linear Mini PLS
basic unit
|
| *For slave unit, change the A in SAC to S *For 220/440 VAC 50/60 hz AC power input change the C in SAC to 2 |
|
| 2.
Output Modules
|
|
| Select type and number of optically isolated logic level output cam modules:
|
|
ASY-M1250-08TI |
TTL outputs, cam module with terminal block
|
ASY-M1250-08TD |
8 TTL outputs, with 15-pin sub D connector |
ASY-M1250-08PI |
8 PNP outputs, cam module with terminal block |
ASY-M1250-08PD |
8 PNP outputs, with 15-pin sub D connector |
ASY-M1250-08NI |
8 NPN outputs, cam module with terminal block |
ASY-M1451-LCAMP |
Logic Cam output module. Accepts 8 inputs (PNP sourcing) and logic-ANDs each of the 8 PLS outputs with respective input; has a 9-pin and a 15-pin subD connector for interconnection. PNP sourcing outputs. |
| ASY-M1451-LCAMN | Logic Cam output module. Accepts 8 inputs (PNP sourcing) and logic-ANDs each of the 8 PLS outputs with respective input; has a 9-pin and a 15-pin subD connector for interconnection. PNP sourcing outputs. NPN (sinking) outputs. |
| Select type and number of optically isolated power output cam modules | |
ASY-M1250-08AC
|
8 Output, 120 VAC @ 0.5 A each output, 4 A max. per module, with terminal block |
ASY-M1250-08DC
|
8 Output, 10-28 VDC @ l A each output, 4 A max. per module, with terminal block |
| Select type and number of special (Position or Tach) modules. (Maximum of two modules from this category may be used in a PLS) | |
| ASY-M1250-20MAP | Analog position/tach module; 4-20 mA current PNP (sourcing) sourcing output |
| ASY-M1250-20MAN | Above with current NPN (sinking) output |
| ASY-M1250-010V | Above with 0-10 V analog output |
| ASY-M1250-X1 X2 X3 | Digital position and Tach output modules |
| X1 = Output Format: | |
| BCD: | BCD position |
| TAC: | Digital TACH; BCD output |
| GRY: | Standard Gray code |
| X2 = PC Handshake: | |
| 1: | With PC sync circuit |
| 0: | Without PC sync circuit |
| X3 = Output Type: | |
| T: | TTL with multiplexing |
| P: | PNP (sourcing) transistor |
| N: | NPN (sinking) transistor |
| Select type of serial communication module to be used with SAC-M1450-300 PLS | |
| ASY-M1250-SER2 | Bidirectional RS-232C serial communication module |
| ASY-M1250-SER2L | Above module with long-line serial communication |
| ASY-M1250-SER4 | Bidirectional RS-422A serial communication module |
| Select cable for wiring logic level cam or special modules to external devices (8 outputs per cable): | |
| xxx = length in ft, 010, 025, 050, and 050 ft. increments, e.g., 100, 150, 200 ft., etc. | |
| CBL-09S22-DAxxx | 9-conductor, cable with overall foil shield, and 9-pin sub D connector on one end |
| CBL-15S22-DAxxx | 15-conductor, cable with overall foil shield and 15-pin sub D connector on one end |
| CBL-18S22-Cxxx | 18-conductor shielded cable for use with modules with terminal block |
| ECM-15PIN-M11 | 15-pin male DSub connector |
| ECM-09PIN-M11 | 9-pin male DSub connector |
| 4. Remote Power Relay Output Chassis | |
| Select type and number of output chassis: (must use NPN (sinking)-type output module. Relays not included. | |
| ASY-RLYCH-08RL | Chassis for 8 electromechanical SPDT relay outputs (Use with KSD-012DC-10A SPDT relay only) |
| ASY-RLYCH-16RL | Above with 16 electromechanical SPDT relay outputs (Use with KSD-012DC-10A SPDT relay only |
| ASY-RLYCH-08SS | Chassis for 8 solid-state relay outputs or electromechanical SPST outputs using KSD-A12DC-10A relays |
| ASY-RLYCH-16SS | Above chassis for 16 solid-state relay outputs or electromechanical SPST outputs using KSD-A12DC-10A relays |
| *For 220/240 VAC, 50/60 Hz, AC power input on above chassis, change the Y in "ASY" to 2 | |
| Select type and number of output relays: (required in ASY-RLYCH-xxx relay chassis) | |
| KSD-012DC-10A | Electromechanical relay, SPDT, Form C, 120 VAC @ l0 A resistive (for use with ASY-RLYCH-xxRL relay chassis only) |
| KSS-120AC-3AMP | Solid-state relay, 120 VAC @ 3 A |
| KSS-60VDC-3AMP | Solid-state relay, 10-60 VDC @ 3 A |
| KSS-200DC-lAMP | Solid-state relay, 200 VDC @ l A |
| KSD-A12DC-10A | Electromechanical relay, SPST, Form A, 120 VAC @ 10 A, resistive |
| Cable connecting cam modules to relay chassis (8 outputs per cable): | |
| CBL-RLYCH-DA4 | 15-conductor cable, with overall foil shield, 4 ft length and sub D connector on both ends, for interconnection of relay chassis to the PLS |
| CBL-RLYCH-D04 | 15-conductor cable, with overall foil shield, 4 ft length and sub D connector on one end and open on the other, for interconnection of relay chassis to the PLS cam module |
| CL-15S22-DAxxx | Same as above with extended lengths. xxx = length in ft., 010, 025, 050, and 50 ft. increments, e.g., 100, 150, 200 ft., etc. |
| Brake Input to the PLS Relay: | |
| ASY-BRAKE-RLY | Relay including socket required to wire brake input to the PLS, 120 VAC coil |
5. MINI•PLS with Built-in Power Relay Output Chassis,, Back-Panel, or Nema 12 (IP52) Enclosure Mounting |
|
| Select appropriate system: | |
| SAC-MX1-X2 X3 | MINI•PLS system for back-panel mounting with cam modules, power output chassis, and relays |
| X1 = Basic Model: | |
| 1250: | The M1250 MINI•PLS |
| 1450: | The M1450 MINI•PLS |
| 1451: | The M1451 Mini•PLS |
| X2 = Type of power relay outputs: | |
| 16RL: | 16 electromechanical relay outputs, 120 VAC @ 10 A |
| 16AC: | 16 solid-state AC relay outputs, 120 VAC @ 3 A |
| 16DC: | 16 solid-state DC relay outputs, 9-60 VDC @ 3 A |
| 16AD: | 8 solid-state AC relays, 120 VAC @ 3 A and 8 solid-state DC relays, 9-60 VDC @ 3 A |
| 32RL: | 32 EM-relay outputs, 120 VAC @ 10 A |
| 32AC: | 32 solid-state AC relay outputs, 120 VAC @ 3 A |
| 32DC: | 32 solid-state DC relay outputs, 9-60 VDC @ 3 A |
| 40RL: | 40 EM-relay outputs, 120 VAC @ 10 A |
| 40AC: | 40 solid-state AC relay outputs, 120 VAC @ 3 A |
| 40DC: | 40 solid-state DC relay outputs, 9-60 VDC @ 3A |
| X3 = Type of MINI•PLS: | |
| 0: | 3-digit, single-turn rotary PLS (model M1250) |
| 1: | 3-digit, single-turn rotary PLS with ModZ and speed compensation (model M1450-300) |
| 2: | 3-digit, single-turn rotary PLS with multiple rate offsets model M1450-MROF) |
| 3: | 4-digit, single-turn rotary PLS with ModZ and speed compensation (model M1450-400) |
| 4: | 6-digit, multi-turn, single resolver linear PLS (model M1450-M10) |
| 5: | 6-digit, 64:1 ratio, multi-turn linear PLS (model M1450-D64) |
| 6: | 6-digit, 128:1 ratio, multi-turn linear PLS (model M1450-D128) |
| 7: | 6-digit, linear PLS (model M1450-LTO) |
| 8: | 3-digit, single-turn rotary PLS with ModZ/Brake Monitor, speed compensation, and serial communication capabilities (model M1451-010) |
| Select part number of output chassis for back panel mount unit only: (Relays not included, see below to order) |
|
| ASY-OUTPT-16RL | Chassis for 16 electromechanical, DPDT relay outputs |
| ASY-OUTPT-16SS | Chassis for 16 solid-state relay outputs |
| ASY-OUTPT-16RS | Chassis for 8 electromechanical DPDT relay and 8 solid-state relay outputs |
| Select type and number of output relays: (Required for ASY-OUTPT-xxxx relay chassis) | |
| KDD-012DC-10SIG | 10 A (any VAC as long as does not exceed 10 A) DPDT electromechanical relay |
| KSS-120AC-ERI | 3 A, 120 VAC, solid-state AC relay module |
| KSS-055DC-ERI | 2 A, 3-40 VDC, solid-state DC relay module |
| KSS-AC/DC-ERI | Low leakage (<0.1 mA), AC/DC solid-state relay module, 135 VAC (rms) @ 0.35 A or 190 VDC (max.) @ 0.5 A |
| Select appropriate enclosure, if required: | |
| ENC-M1250-N16 | NEMA 12 (IP52) enclosure for 16-channel PLS |
| ENC-M1250-W16 | Above enclosure with see-through window |
| ENC-M1250-N32 | NEMA 12 (IP52) enclosure for 32-channel PLS |
| ENC-M1250-W32 | Above enclosure with see-through window |
| ENC-M1250-N40 | NEMA 12 (IP52) enclosure for 40-channel PLS |
| Spare Parts: | |
| EEC-15PIN-0TB | 15-position terminal block for main terminal block on M1250 and for cam modules |
| EEC-18PIN-0TB | 18-position Main terminal block for M1450/M1451 |
| MCP-M1250-011 | Cover plate for unoccupied cam module space |
| ECM-15PIN-M11 | 15-Pin sub D male connector |
| CBL-M1250-INPUT | M1250 to main terminal block connector for back panel mounted systems |
| CBL-M1250-OUTPUT | M1250/M1450 to output chassis for back panel mount systems |
| CBL-M1450-INPUT | M1450 to main terminal block connector for back panel mounted systems |