M2020 Die Set Control System
| 1.
M2020 Series Die Set (Complete System)
|
|
| Resolver based complete
system
|
|
| SAC-M2020-S128
|
Complete Single die set
control system for automatic die positioning. The system stores set-up
information for up to 255 dies. The resolver based system includes: 1 output
card, power output chassis with interconnecting cable (4 ft.) 1 resolver
(RL210) with built-in 128:1 gear ratio, and 1 Die select module. (Resolver
cable and relays are not included)
|
| SAC-M2022-S128
|
Above for dual die set
control includes 2 resolvers, 2 output modules, 1 Die select module
|
| SAC-M2020-SCA
|
Complete single die set
control system for automatic die set positioning with counter-balance
control. The system stores setup information for up to 255 dies. The system
includes: base unit with 1 input card, 1 output card, 1 counter balance card
with analog 4-20mA input, 1 power output relay chassis with relays and 4 ft.
interconnecting cable, 1 dual brushless resolver with built-in 128:1 gear
train (Resolver cable not included)
|
| SAC-M2022-SCA
|
Same as SAC-M2020-SCA
except with dual die set control: 2 output cards, 2 resolvers and 2 power
output relays with 2 interconnecting cables.
|
| SAC-M2020-SCV
|
Complete single die set
control system for automatic die set positioning with counter-balance
control. The system stores setup information for up to 255 dies. The system
includes: base unit with 1 input card, 1 output card, 1 counter balance card
with analog 0-10V DC input, 1 power output relay chassis with relays and 4
ft. interconnecting cable, 1 dual brushless resolver with built-in 128:1 gear
train (Resolver cable not included)
|
| SAC-M2022-SCV
|
Same as SAC-M2020-SCV
except with dual die set control: 2 output cards, 2 resolvers and 2 power
output relays with 2 interconnecting cables. (Resolver cable not included)
|
| Linear Transducer based
complete system (Does not include Linear Transducer)
|
|
| SAC-M2020-SLIN
|
Complete Single die set
control system for automatic die positioning. The system stores setup
information for up to 255 dies. The Linear Transducer based system includes:
1 output card, power output chassis with interconnecting cable (4 ft.), 1 Die select module. (Transducer rod not included)
|
| SAC-M2022-SLIN
|
Above for dual die set
control with 2 output modules, 1 Die select module. (Transducer rods not
included)
|
| 2.
Linear Transducer Rods for use with M202x-LIN
|
|
| Autotech offers linear
transducer rods, part number SAC-LT140-xxx, where xxx is the length of the
transducer rod. The standard lengths available are 12, 24, 36, 48, 60, 72,
84, 96 and 108 inches. The transducer rod requires an interface box and a
connecting cable. Please see page 32 for ordering information.
|
|
| 3.
Resolver Cables
|
|
| CBL-RL210-Mxxx
|
22 AWG, 10 conductor (5
twisted pairs) overall foil shielded cable, with 19 pin MS connector (xxx =
number of ft.) (ECM - 19REC-ITT) on one end (for fuel turn resolvers)
|
| 4. Output Relay
|
|
| Select number of relays
required.
|
|
| KSD-012DC-10A
|
Electro-mechanical relay
SPDT, 120 VAC @ 10 amps resistive (Note: for use with ASY-RLYCH-08RI relay
chassis only)
|
| 5.
System Components for Spare Parts
|
|
| SAC-M2020-010
|
Resolver based, Single
die set control, basic and without any I/O’s, resolver or cable
|
| SAC-M2022-010
|
Above for dual die set
control
|
| SAC-M2020-L10
|
Linear transducer based,
Single die set control, basic unit without any I/O’s, rod or cable
|
| SAC-M2022-L10
|
Above for dust die set
control
|
| ASY-M2020-INPUT
|
Die select module, used
with Die ID box
|
| ASY-M2020-OTPUT
|
Output card, 8 outputs
|
| ASY-RLYCH-08RL
|
Chassis for up to 8 EM
relays
|
| ASY-M2020-DIID
|
Die ID Box (Required one
for each die)
|
| CBL-RLYCH-DA4
|
15 conductor cable with
overall foil shield, 4 ft. length and DSub connector on both ends for
interconnection of relay chassis to M2020 or M2022 (8 outputs per cable)
|
Note: For Part Numbers and Price of individual components, cables & accessories, Ultrasonic linear transducers, CAM modules, relay chassis and other product variations such as additional PLS outputs, call the factory.